three-point bending造句
例句與造句
- Shear and three - point bending test of animal bones
動物骨的剪切和三點彎曲試驗 - The measurement of crack initiation in three - point bending fatigue of 40cr steel
鋼疲勞裂紋萌生壽命的測量 - The dynamic response of stress intensity factor of three - point bending specimen
三點彎曲試樣應力強度因子的動態響應 - Standard test method for distortion temperature in three - point bending by thermomechanical analysis
熱機分析三點彎曲處變形溫度的標準試驗方法 - Standard test method for measuring the dynamic mechanical properties : in flexure three - point bending
利用三點彎曲管對塑料動力機械性能測量的標準試驗方法 - It's difficult to find three-point bending in a sentence. 用three-point bending造句挺難的
- Vibration analysis method used for determining the dynamic stress intensity factor of three - point bending specimen
三點彎曲試樣動應力強度因子求解的振動分析方法 - A research of the crack propagation of concrete non - standard three - point bending beam by photo - elastic method
光彈性貼片法研究混凝土非標準三點彎曲梁裂縫擴展過程 - Analysis of dynamic response of stress intensity factor of three - point bending specimen by using finite element method
三點彎曲試樣應力強度因子動態響應的有限元分析 - Evaluation of fracture toughness of three - point bend specimen from the instrumented impact test based on the local approach
基于局部法由示波沖擊試驗對斷裂韌性的預測 - Plastics and composites . determination of the bending fatigue properties . part 3 : three - point bending test on unsecured test pieces
塑料制品及復合材料.彎曲疲勞特性的測定.第3部分:不固定試件的三點式彎曲試驗 - Table 4 . 1 for three - point bend specimens shows that the ratio of support span to specimen depth has a small but definite effect on the results
表4 1的三點彎曲試樣表明,支撐跨距對試樣高度的比值對試驗結果有微小而又確定的影響。 - Standard test method for determination of modulus of elasticity for rigid and semi - rigid plastic specimens by controlled rate of loading using three - point bending
用三點彎曲法測定在裝載控制速度下剛性和半剛性塑料樣品的彈性模量的標準試驗方法 - The damage introduced by single and 5 repeated thermal shocks ( water - quench experiments ) was characterized by degradation of flexural strength in three - point bending
單次和5次重復熱震(水淬試驗)后經三點抗彎測試來觀察材料抗彎強度的衰減情況。 - In this paper , the program ls - dyna was used . the model was validated by simulating the tibia three - point bending test and lower extremity sheering and bending tests
模型的有效性通過模擬脛骨的彎曲實驗和下肢的剪切與彎曲實驗,并比照相同條件下的生物試驗結果驗證。 - Abstract : the inertial effect of three - point bend specimens under impactloading was analyzed by using the spring - mass system model and an expression for the correction of inertial force was obtained under the condition of brittle fracture of materials
文摘:用彈簧質量模型分析了三點彎曲試樣在沖擊載荷作用下的慣性效應,得到了脆性斷裂條件下有效載荷的修正公式。
更多例句: 下一頁